UltraViolet Devices High Output UV Device V-Flex Instrukcja Instalacji

This manual covers the preliminary installation, operation and generalmaintenance requirements for Aquafine Ultraviolet Water TreatmentEquipment for t

10Quartz sleeve installationCompression nut assembled on the quartz sleeveStainless socket & lamp end cover designCompression Nut Tool - Rotate cl

11single-ended lamp design for unitsmanufactured after January 1, 1999Once it has been verified that there are no leaks in the system, the UVlamps are

12double-ended lamp design for unitsmanufactured prior to Jan. 1, 19991. Remove all power to the UV unit.2. Depressurize the system.3. Wear clean cott

13morehigh-temperature (HT) unitsOnce it has been verified that there are no leaks in thesystem, the UV lamps are ready for installation.1. Remove all

14Lamp socket ID number on end plateSecure lamp socket connector to lampInsert the lamp in a level, horizontal position.Screw the lamp socket cap into

15prior to turning on the UV unit,the following must be verified:• With water flowing through the system, ensure thatthere are no system leaks and no

16UV lamp operational display panelTo verify that all the UV lamps are operating properly, your UVtreatment unit has been provided with a UV Lamp Oper

17model S-254 UV optical sensoroptionThe optional S-254 UV optical sensor measures therelative output of ultraviolet light within the UVtreatment cham

18moreIt is essential that all non-operationallamps be changed immediately tomaintain system efficiency.temperaturesafety control option*The Temperatu

19using the LED displayIf an LED bulb does not light after you replace a UV lamp, youneed to verify the electrical output of the ballast connected to

2Installation and Operational Safety ... 3Description of EquipmentRBE Series ...

20cleaning the unitThe exterior surfaces of the Aquafine UV unit should bekept clean as part of routine maintenance. Use a soft clothwith soap and wat

21more6. Replace the probe and the coaxial cable.7. Turn the power “on” and resume operation.Whenever new lamps have been installed,follow all resetti

22Ballast connectorsmoreballast replacementBallast replacement is not part of the UV unit’s routinemaintenance. However, in the event that a ballast n

23Refer to this nameplate decal on yourunit when ordering parts or service.general part description... part number

24moredouble-ended units cont. ... part number13. UV Lamps DE Standard 185-BlueTOC Reduction ApplicationsSiz

25single-ended units cont. ... part number28. UV Lamps SE Validated 185-YellowTOC Reduction ApplicationsSiz

26Note: Some units are factory supplied with stainless steel NPT threadedclosure plugs to seal the 1/4” sample ports. Teflon tape is temporarilyapplie

3DO NOT LOOKAT UV LIGHT8. Do not allow the unit to overheat by operatingwithout water flow. Normal operating temperature forstandard UV units is 50° t

4To maintain your UV units warranty, please complete andreturn the Warranty Registration Card located in theback pocket of this manual.The following

5moreAquafine equipment is guaranteed to be free fromdefects in materials and workmanship (excludingultraviolet lamps) for a period of one year from t

6pressure may rupture and fracture the quartz sleeves.operating pressureStandard units are rated for a maximum operatingpressure of 120 psig (8.24 bar

7morecan then proceed with the installation of the quartz sleeves.intermittent operationNever operate the unit without water flow. Permanentdamage is

8The procedures on this and the following page apply toDouble-Ended (DE), Single-Ended (SE) and High Tempera-ture (HT) RBE units.quartz sleeve install

9moreOver tightening can break thequartz sleeves or create leaks.Place end of quartz sleeve into threaded nippleRemove socket coversquartz sleeve repl